First Test: T-Drill T-35 Tee-Forming Tool Wantagh NY

A T-Drill is a unique, incredible plumber's tool in Wantagh that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

Local Companies

Roberts Plywood Co.
800-422-4944
45 North Industry Court
Deer Park, NY
Lowe's
(631) 927-3470
90 Price Parkway
Farmingdale, NY
Ace Hardware of Rockville Centre
(516) 568-2301
315 Sunrise Hwy, between Morris and N.Park
Rockville Centre, NY
The Home Depot
(516)546-6280
160 E. Sunrise Hwy
Freeport, NY
Hicksville - A
(516) 733-3000
195 N Broadway
Hicksville, NY
EXOTIC WOODS USA
(631) 651-8651
698 Fort Salonga Rd
Northport, NY
Suburban Mills
631-351-6445
16 Railroad St
Huntington Station, NY
Fastenal- Hicksville
516-942-2640
73 Bloomingdale Rd Hicksville, NY, 11801
Hicksville, NY
Brite Hardware Auto Parts, Inc
718-849-8121
112-15 Jamaica Avenue
Jamaica, NY
Kmart 9419 / Cross Merch
(718) 821-2412
66-26 Metropolitan Ave
Middle Vlg, NY
Data Provided by:
  

Provided By:

Source: TOOLS OF THE TRADE Magazine
Publication date: September 12, 2007

By Michael Springer

A T-Drill is a unique, incredible plumber's tool that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

A T-Drill pulls a tee out of a continuous run of copper tubing. It consists of a drill motor with a high-tech business end that does the holding, drilling, and forming. Here's how it works: support legs at the head of the drill hold it centered on a piece of tubing. With the desired outlet-size T-Drill head attached, a pilot hole is drilled into the tube; then, with the bit still in the tube, two forming pins built into the pilot bit are extended by rotating a collar on the head.

After engaging the reverse-feed mechanism lever, the support legs push against the tubing, and the spinning forming pins back out of the tube, leaving a tee outlet of the proper size. And all of this is done in mere seconds.

Then the branch, or outlet, section of tubing is prepared by placing it in a T-Drill notcher, where it is cut to the sameradius as the tube run so the branch does not project into the run of tube. The notcher also leaves two dimples on the branch. These serve as a depth stop, an alignment guide, and provide for easy inspection of the joint.

Click here to read full article from Tools of the Trade

Related Articles
- Festool Joining System Wantagh NY
Festool's Domino isn't just a brand new type of joining tool; it's a whole new joining system. Based on mortise-and-tenon joinery, the Domino combines the qualities of biscuits and dowels with a stronger, self-aligning joint.
- Graphisoft EcoDesigner Wantagh NY
- Hand Tools Wantagh NY
- Framing Square Wantagh NY
- INNOVA® 3100 Tools Wantagh NY
- Festool C12 Cordless Drill Wantagh NY
- Drywall Cutting and Multifunction Bench Wantagh NY
- Home Repair Tools Wantagh NY
- Hitachi KM 12VC Router Combination Kit Wantagh NY
- Hidden-Fastener Tool Wantagh NY