First Test: T-Drill T-35 Tee-Forming Tool Plainview NY

A T-Drill is a unique, incredible plumber's tool in Plainview that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

Local Companies

Roberts Plywood Co.
800-422-4944
45 North Industry Court
Deer Park, NY
ABC Supply Co.,Inc/Bohemia
631-285-7710
2950 Veterans Memorial Hwy Bohemia, NY, 11716
Bohemia, NY
Ferreteria Solar El Almacigo, Inc
(787) 856-2670
Bo Almacigo Bajo Carr 371 Km 1.4
Yauco, NY
The Home Depot
(631)242-0215
475 Commack Road
Deer Park, NY
Kmart 3862 / Cross Merch
(631) 567-3060
5151 Sunrise Hwy
Bohemia, NY
EXOTIC WOODS USA
(631) 651-8651
698 Fort Salonga Rd
Northport, NY
Suburban Mills
631-351-6445
16 Railroad St
Huntington Station, NY
Fastenal- Farmingdale
631-391-0980
61 D Carolyn Blvd Farmingdale, NY, 11735
Farmingdale, NY
Ferreteria Valois Pagan
(787) 844-2460
1478 Ave Tito Castro
Ponce, NY
The Home Depot
(718)977-2081
13220 Merrick Blvd
Jamaica, NY
Data Provided by:
  

Provided By:

Source: TOOLS OF THE TRADE Magazine
Publication date: September 12, 2007

By Michael Springer

A T-Drill is a unique, incredible plumber's tool that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

A T-Drill pulls a tee out of a continuous run of copper tubing. It consists of a drill motor with a high-tech business end that does the holding, drilling, and forming. Here's how it works: support legs at the head of the drill hold it centered on a piece of tubing. With the desired outlet-size T-Drill head attached, a pilot hole is drilled into the tube; then, with the bit still in the tube, two forming pins built into the pilot bit are extended by rotating a collar on the head.

After engaging the reverse-feed mechanism lever, the support legs push against the tubing, and the spinning forming pins back out of the tube, leaving a tee outlet of the proper size. And all of this is done in mere seconds.

Then the branch, or outlet, section of tubing is prepared by placing it in a T-Drill notcher, where it is cut to the sameradius as the tube run so the branch does not project into the run of tube. The notcher also leaves two dimples on the branch. These serve as a depth stop, an alignment guide, and provide for easy inspection of the joint.

Click here to read full article from Tools of the Trade

Related Articles
- Hidden-Fastener Tool Plainview NY
Premium synthetic decks are the heart of my deck-building business, and I use hidden fasteners on all of my projects. In fact, I’m so familiar with hidden clips and screws that I almost wince just typing about them.
- Festool C12 Cordless Drill Plainview NY
- INNOVA® 3100 Tools Plainview NY
- Hitachi KM 12VC Router Combination Kit Plainview NY
- Framing Square Plainview NY
- Home Repair Tools Plainview NY
- Drywall Cutting and Multifunction Bench Plainview NY
- Hand Tools Plainview NY
- Graphisoft EcoDesigner Plainview NY
- Festool Joining System Plainview NY