First Test: T-Drill T-35 Tee-Forming Tool Massapequa NY

A T-Drill is a unique, incredible plumber's tool in Massapequa that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

Local Companies

Roberts Plywood Co.
800-422-4944
45 North Industry Court
Deer Park, NY
Costello's Ace Hardware
(631) 321-1316
515 Montauk Hwy, Big Lots and Pathmark
West Babylon, NY
The Home Depot
(718)661-4608
124-04 31st Avenue
Flushing, NY
Green Acres Mall
(516) 256-5700
1150 Sunrise Hwy
Valley Stream, NY
Huntington Sq Mall
(631) 462-2100
4000 Jericho Tpke
E Northport, NY
EXOTIC WOODS USA
(631) 651-8651
698 Fort Salonga Rd
Northport, NY
Suburban Mills
631-351-6445
16 Railroad St
Huntington Station, NY
ACE TOOL REPAIR INC
(516) 783-8899
2201 WANTAGH AVE WANTAGH, NY, 11793
Wantagh, NY
The Home Depot
(516)546-6280
160 E. Sunrise Hwy
Freeport, NY
Garden City - A
(516) 873-3700
1111 Franklin Ave
Garden City, NY
Data Provided by:
  

Provided By:

Source: TOOLS OF THE TRADE Magazine
Publication date: September 12, 2007

By Michael Springer

A T-Drill is a unique, incredible plumber's tool that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

A T-Drill pulls a tee out of a continuous run of copper tubing. It consists of a drill motor with a high-tech business end that does the holding, drilling, and forming. Here's how it works: support legs at the head of the drill hold it centered on a piece of tubing. With the desired outlet-size T-Drill head attached, a pilot hole is drilled into the tube; then, with the bit still in the tube, two forming pins built into the pilot bit are extended by rotating a collar on the head.

After engaging the reverse-feed mechanism lever, the support legs push against the tubing, and the spinning forming pins back out of the tube, leaving a tee outlet of the proper size. And all of this is done in mere seconds.

Then the branch, or outlet, section of tubing is prepared by placing it in a T-Drill notcher, where it is cut to the sameradius as the tube run so the branch does not project into the run of tube. The notcher also leaves two dimples on the branch. These serve as a depth stop, an alignment guide, and provide for easy inspection of the joint.

Click here to read full article from Tools of the Trade

Related Articles
- Hand Tools Massapequa NY
The Sonic Tape, a distance-measuring device from AGL Lasersource can be used to determine length, width, and height and to compute area and volume. The tool has a range from 2 feet to 50 feet and an accuracy of 99.5 percent.
- Festool Joining System Massapequa NY
- INNOVA® 3100 Tools Massapequa NY
- Home Repair Tools Massapequa NY
- Festool C12 Cordless Drill Massapequa NY
- Hitachi KM 12VC Router Combination Kit Massapequa NY
- Drywall Cutting and Multifunction Bench Massapequa NY
- Graphisoft EcoDesigner Massapequa NY
- Hidden-Fastener Tool Massapequa NY
- Framing Square Massapequa NY