First Test: T-Drill T-35 Tee-Forming Tool Lindenhurst NY

A T-Drill is a unique, incredible plumber's tool in Lindenhurst that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

Local Companies

Roberts Plywood Co.
800-422-4944
45 North Industry Court
Deer Park, NY
Costello's Ace Hardware
(631) 467-6565
2120 Middle Country Rd, Pathmark
Centereach, NY
Lowe's of Stony Brook, NY
631-406-2015
2150 Nesconset Highway Stony Brook, NY, 11790
Stony Brook, NY
Islip True Value Hardware
(631) 581-0951
445 Main St
Islip, NY
Kmart 9381 / Cross Merch
(631) 421-5005
839 New York Avenue
Huntington, NY
EXOTIC WOODS USA
(631) 651-8651
698 Fort Salonga Rd
Northport, NY
Suburban Mills
631-351-6445
16 Railroad St
Huntington Station, NY
DYNAMITE TOOL CO
(631) 563-8181
1551 SMITHTOWN AVENUE BOHEMIA, NY, 11716
Bohemia, NY
Brinkmann Hardware
(631) 363-2116
125 Montauk Hwy
Blue Point, NY
The Home Depot
(631)580-7849
255 Pond Path
South Setauket, NY
Data Provided by:
  

Provided By:

Source: TOOLS OF THE TRADE Magazine
Publication date: September 12, 2007

By Michael Springer

A T-Drill is a unique, incredible plumber's tool that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

A T-Drill pulls a tee out of a continuous run of copper tubing. It consists of a drill motor with a high-tech business end that does the holding, drilling, and forming. Here's how it works: support legs at the head of the drill hold it centered on a piece of tubing. With the desired outlet-size T-Drill head attached, a pilot hole is drilled into the tube; then, with the bit still in the tube, two forming pins built into the pilot bit are extended by rotating a collar on the head.

After engaging the reverse-feed mechanism lever, the support legs push against the tubing, and the spinning forming pins back out of the tube, leaving a tee outlet of the proper size. And all of this is done in mere seconds.

Then the branch, or outlet, section of tubing is prepared by placing it in a T-Drill notcher, where it is cut to the sameradius as the tube run so the branch does not project into the run of tube. The notcher also leaves two dimples on the branch. These serve as a depth stop, an alignment guide, and provide for easy inspection of the joint.

Click here to read full article from Tools of the Trade

Related Articles
- Festool Joining System Lindenhurst NY
Festool's Domino isn't just a brand new type of joining tool; it's a whole new joining system. Based on mortise-and-tenon joinery, the Domino combines the qualities of biscuits and dowels with a stronger, self-aligning joint.
- Framing Square Lindenhurst NY
- Hand Tools Lindenhurst NY
- Home Repair Tools Lindenhurst NY
- Drywall Cutting and Multifunction Bench Lindenhurst NY
- Graphisoft EcoDesigner Lindenhurst NY
- Hitachi KM 12VC Router Combination Kit Lindenhurst NY
- INNOVA® 3100 Tools Lindenhurst NY
- Festool C12 Cordless Drill Lindenhurst NY
- Hidden-Fastener Tool Lindenhurst NY