First Test: T-Drill T-35 Tee-Forming Tool Holbrook NY

A T-Drill is a unique, incredible plumber's tool in Holbrook that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

Local Companies

Roberts Plywood Co.
800-422-4944
45 North Industry Court
Deer Park, NY
Costello's Ace Hardware
(631) 422-5566
448 Union Blvd
West Islip, NY
Lowe's of Stony Brook, NY
631-406-2015
2150 Nesconset Highway Stony Brook, NY, 11790
Stony Brook, NY
Suffolk Supply True Value
(631) 924-3935
1504 Rocky Point Rd
Middle Island, NY
Lindenhurst -Sears Hardware Stores
(631) 957-7210
600 N Wellwood Ave
Lindenhurst, NY
EXOTIC WOODS USA
(631) 651-8651
698 Fort Salonga Rd
Northport, NY
Suburban Mills
631-351-6445
16 Railroad St
Huntington Station, NY
Fastenal- Holbrook
631-218-3485
920 Lincoln Ave Holbrook, NY, 11741
Holbrook, NY
Brinkmann True Value Hdwe
(631) 567-6879
15 Foster Ave
Sayville, NY
Kmart 3862 / Cross Merch
(631) 567-3060
5151 Sunrise Hwy
Bohemia, NY
Data Provided by:
  

Provided By:

Source: TOOLS OF THE TRADE Magazine
Publication date: September 12, 2007

By Michael Springer

A T-Drill is a unique, incredible plumber's tool that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

A T-Drill pulls a tee out of a continuous run of copper tubing. It consists of a drill motor with a high-tech business end that does the holding, drilling, and forming. Here's how it works: support legs at the head of the drill hold it centered on a piece of tubing. With the desired outlet-size T-Drill head attached, a pilot hole is drilled into the tube; then, with the bit still in the tube, two forming pins built into the pilot bit are extended by rotating a collar on the head.

After engaging the reverse-feed mechanism lever, the support legs push against the tubing, and the spinning forming pins back out of the tube, leaving a tee outlet of the proper size. And all of this is done in mere seconds.

Then the branch, or outlet, section of tubing is prepared by placing it in a T-Drill notcher, where it is cut to the sameradius as the tube run so the branch does not project into the run of tube. The notcher also leaves two dimples on the branch. These serve as a depth stop, an alignment guide, and provide for easy inspection of the joint.

Click here to read full article from Tools of the Trade

Related Articles
- INNOVA® 3100 Tools Holbrook NY
The INNOVA 3100 single item alone is believed to account for as much as 20 percent of all OBD2 tool sales in the U.S., according to industry and internal calculations. Equus has doubled its retail customer base and tripled its sales over the past six years, adding a mix of mass merchandise, online, catalog and tool distributors.
- Drywall Cutting and Multifunction Bench Holbrook NY
- Festool Joining System Holbrook NY
- Hand Tools Holbrook NY
- Hitachi KM 12VC Router Combination Kit Holbrook NY
- Framing Square Holbrook NY
- Festool C12 Cordless Drill Holbrook NY
- Home Repair Tools Holbrook NY
- Hidden-Fastener Tool Holbrook NY
- Graphisoft EcoDesigner Holbrook NY