First Test: T-Drill T-35 Tee-Forming Tool Copiague NY

A T-Drill is a unique, incredible plumber's tool in Copiague that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

Local Companies

Roberts Plywood Co.
800-422-4944
45 North Industry Court
Deer Park, NY
ABC Supply Co.,Inc/Hicksville
516-822-2900
55 Ludy Street Hicksville, NY, 11801
Hicksville, NY
Caguas Commercial
(787) 743-4001
Carretera 189 Km 2.5
Caguas, NY
Islip True Value Hardware
(631) 581-0951
445 Main St
Islip, NY
The Home Depot
(516)565-3700
172 Fulton Ave
Hempstead, NY
EXOTIC WOODS USA
(631) 651-8651
698 Fort Salonga Rd
Northport, NY
Suburban Mills
631-351-6445
16 Railroad St
Huntington Station, NY
County Line Do it Best Hdwe
631-427-4455
173 West Hills Road
Huntington Station, NY
Ferreteria Solar El Almacigo, Inc
(787) 856-2670
Bo Almacigo Bajo Carr 371 Km 1.4
Yauco, NY
The Home Depot
(516)542-9200
2000 Hempstead Turnpike
East Meadow, NY
Data Provided by:
  

Provided By:

Source: TOOLS OF THE TRADE Magazine
Publication date: September 12, 2007

By Michael Springer

A T-Drill is a unique, incredible plumber's tool that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

A T-Drill pulls a tee out of a continuous run of copper tubing. It consists of a drill motor with a high-tech business end that does the holding, drilling, and forming. Here's how it works: support legs at the head of the drill hold it centered on a piece of tubing. With the desired outlet-size T-Drill head attached, a pilot hole is drilled into the tube; then, with the bit still in the tube, two forming pins built into the pilot bit are extended by rotating a collar on the head.

After engaging the reverse-feed mechanism lever, the support legs push against the tubing, and the spinning forming pins back out of the tube, leaving a tee outlet of the proper size. And all of this is done in mere seconds.

Then the branch, or outlet, section of tubing is prepared by placing it in a T-Drill notcher, where it is cut to the sameradius as the tube run so the branch does not project into the run of tube. The notcher also leaves two dimples on the branch. These serve as a depth stop, an alignment guide, and provide for easy inspection of the joint.

Click here to read full article from Tools of the Trade

Related Articles
- INNOVA® 3100 Tools Copiague NY
The INNOVA 3100 single item alone is believed to account for as much as 20 percent of all OBD2 tool sales in the U.S., according to industry and internal calculations. Equus has doubled its retail customer base and tripled its sales over the past six years, adding a mix of mass merchandise, online, catalog and tool distributors.
- Hand Tools Copiague NY
- Framing Square Copiague NY
- Festool Joining System Copiague NY
- Home Repair Tools Copiague NY
- Hidden-Fastener Tool Copiague NY
- Drywall Cutting and Multifunction Bench Copiague NY
- Graphisoft EcoDesigner Copiague NY
- Festool C12 Cordless Drill Copiague NY
- Hitachi KM 12VC Router Combination Kit Copiague NY