First Test: T-Drill T-35 Tee-Forming Tool Centereach NY

A T-Drill is a unique, incredible plumber's tool in Centereach that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

Local Companies

Roberts Plywood Co.
800-422-4944
45 North Industry Court
Deer Park, NY
Fastenal- Farmingdale
631-391-0980
61 D Carolyn Blvd Farmingdale, NY, 11735
Farmingdale, NY
Costello's Ace Hardware
(631) 694-1100
1102 Broadhollow Rd, Corner of Rte. 110 & Main St.
Farmingdale, NY
Comercial Don Benja
(787) 899-3025
Hc 03 Box 27150 Carr 116 Km 0.8
Lajas, NY
Lindenhurst -Sears Hardware Stores
(631) 957-7210
600 N Wellwood Ave
Lindenhurst, NY
EXOTIC WOODS USA
(631) 651-8651
698 Fort Salonga Rd
Northport, NY
Suburban Mills
631-351-6445
16 Railroad St
Huntington Station, NY
Lowe's of Patchogue
631-687-6220
825 Mantauk Highway East Patchogue, NY, 11772
East Patchogue, NY
Bens True Value Hardware
(631) 775-7435
55b Route 25 (middle Country Road)
Coram, NY
Ferreteria Berrios Inc
(787) 786-2095
Av Comerio #25 Sierra Bayamon
Bayamon, NY
Data Provided by:
  

Provided By:

Source: TOOLS OF THE TRADE Magazine
Publication date: September 12, 2007

By Michael Springer

A T-Drill is a unique, incredible plumber's tool that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

A T-Drill pulls a tee out of a continuous run of copper tubing. It consists of a drill motor with a high-tech business end that does the holding, drilling, and forming. Here's how it works: support legs at the head of the drill hold it centered on a piece of tubing. With the desired outlet-size T-Drill head attached, a pilot hole is drilled into the tube; then, with the bit still in the tube, two forming pins built into the pilot bit are extended by rotating a collar on the head.

After engaging the reverse-feed mechanism lever, the support legs push against the tubing, and the spinning forming pins back out of the tube, leaving a tee outlet of the proper size. And all of this is done in mere seconds.

Then the branch, or outlet, section of tubing is prepared by placing it in a T-Drill notcher, where it is cut to the sameradius as the tube run so the branch does not project into the run of tube. The notcher also leaves two dimples on the branch. These serve as a depth stop, an alignment guide, and provide for easy inspection of the joint.

Click here to read full article from Tools of the Trade

Related Articles
- Hand Tools Centereach NY
The Sonic Tape, a distance-measuring device from AGL Lasersource can be used to determine length, width, and height and to compute area and volume. The tool has a range from 2 feet to 50 feet and an accuracy of 99.5 percent.
- Graphisoft EcoDesigner Centereach NY
- Drywall Cutting and Multifunction Bench Centereach NY
- Hitachi KM 12VC Router Combination Kit Centereach NY
- INNOVA® 3100 Tools Centereach NY
- Home Repair Tools Centereach NY
- Hidden-Fastener Tool Centereach NY
- Festool C12 Cordless Drill Centereach NY
- Framing Square Centereach NY
- Festool Joining System Centereach NY