First Test: T-Drill T-35 Tee-Forming Tool Brentwood NY

A T-Drill is a unique, incredible plumber's tool in Brentwood that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

Local Companies

Roberts Plywood Co.
800-422-4944
45 North Industry Court
Deer Park, NY
Karps Hardware
631-261-1235
2 Larkfield Rd
East Northport, NY
Comercial Don Benja
(787) 899-3025
Hc 03 Box 27150 Carr 116 Km 0.8
Lajas, NY
Brinkmann True Value Hdwe
(631) 567-6879
15 Foster Ave
Sayville, NY
Hauppauge - Sears Hardware Stores
(631) 979-2099
564 Veterans Hwy
Hauppauge, NY
EXOTIC WOODS USA
(631) 651-8651
698 Fort Salonga Rd
Northport, NY
Suburban Mills
631-351-6445
16 Railroad St
Huntington Station, NY
East Islip True Value Lumber
(631) 581-1869
33 Wall St
East Islip, NY
Ferreteria Maderas 3-c Inc.
(787) 783-8260
Calle Segarra Final Sector Bechara
San Juan, NY
The Home Depot
(631)242-0215
475 Commack Road
Deer Park, NY
Data Provided by:
  

Provided By:

Source: TOOLS OF THE TRADE Magazine
Publication date: September 12, 2007

By Michael Springer

A T-Drill is a unique, incredible plumber's tool that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

A T-Drill pulls a tee out of a continuous run of copper tubing. It consists of a drill motor with a high-tech business end that does the holding, drilling, and forming. Here's how it works: support legs at the head of the drill hold it centered on a piece of tubing. With the desired outlet-size T-Drill head attached, a pilot hole is drilled into the tube; then, with the bit still in the tube, two forming pins built into the pilot bit are extended by rotating a collar on the head.

After engaging the reverse-feed mechanism lever, the support legs push against the tubing, and the spinning forming pins back out of the tube, leaving a tee outlet of the proper size. And all of this is done in mere seconds.

Then the branch, or outlet, section of tubing is prepared by placing it in a T-Drill notcher, where it is cut to the sameradius as the tube run so the branch does not project into the run of tube. The notcher also leaves two dimples on the branch. These serve as a depth stop, an alignment guide, and provide for easy inspection of the joint.

Click here to read full article from Tools of the Trade

Related Articles
- Festool C12 Cordless Drill Brentwood NY
Festool C12 is the best 12-volt drill/driver I've ever used. As powerful and versatile as it is small, Festool's C12 sets a new category standard. I tested it drilling small and large holes, driving various lengths of wood screws and Tapcons, and even mixing thinset. The C12 was a great tool at every step.
- Hitachi KM 12VC Router Combination Kit Brentwood NY
- Drywall Cutting and Multifunction Bench Brentwood NY
- Graphisoft EcoDesigner Brentwood NY
- Framing Square Brentwood NY
- INNOVA® 3100 Tools Brentwood NY
- Festool Joining System Brentwood NY
- Hidden-Fastener Tool Brentwood NY
- Hand Tools Brentwood NY
- Home Repair Tools Brentwood NY