First Test: T-Drill T-35 Tee-Forming Tool Amityville NY

A T-Drill is a unique, incredible plumber's tool in Amityville that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

Local Companies

Roberts Plywood Co.
800-422-4944
45 North Industry Court
Deer Park, NY
Costello's Ace Hardware
(516) 644-2450
3899 Hempstead Tpke, Pathmark
Bethpage, NY
Comercial Berrios Inc
(787) 739-2831
Barcelo #64
Cidra, NY
The Home Depot
(631)666-3800
1881 Sunrise Hwy
Bay Shore, NY
N Babylon/Deer Pk - Sears Hardware Stores
(631) 667-3958
20 Deer Shore Sq
North Babylon, NY
EXOTIC WOODS USA
(631) 651-8651
698 Fort Salonga Rd
Northport, NY
Suburban Mills
631-351-6445
16 Railroad St
Huntington Station, NY
Trio Hardware
516-935-8385
1032 C Old Country Rd
Plainview, NY
Ferreteria Berrios Inc
(787) 786-2095
Av Comerio #25 Sierra Bayamon
Bayamon, NY
The Home Depot
(516)364-4677
111 Jericho Turnpike
Syosset, NY
Data Provided by:
  

Provided By:

Source: TOOLS OF THE TRADE Magazine
Publication date: September 12, 2007

By Michael Springer

A T-Drill is a unique, incredible plumber's tool that I've relied on to give me a competitive edge for nearly a decade, yet most people–including many plumbers–have never heard of it. So when I was asked to review the new T-35, I was eager to see what kind of improvements they made to this amazing tool.

A T-Drill pulls a tee out of a continuous run of copper tubing. It consists of a drill motor with a high-tech business end that does the holding, drilling, and forming. Here's how it works: support legs at the head of the drill hold it centered on a piece of tubing. With the desired outlet-size T-Drill head attached, a pilot hole is drilled into the tube; then, with the bit still in the tube, two forming pins built into the pilot bit are extended by rotating a collar on the head.

After engaging the reverse-feed mechanism lever, the support legs push against the tubing, and the spinning forming pins back out of the tube, leaving a tee outlet of the proper size. And all of this is done in mere seconds.

Then the branch, or outlet, section of tubing is prepared by placing it in a T-Drill notcher, where it is cut to the sameradius as the tube run so the branch does not project into the run of tube. The notcher also leaves two dimples on the branch. These serve as a depth stop, an alignment guide, and provide for easy inspection of the joint.

Click here to read full article from Tools of the Trade

Related Articles
- Graphisoft EcoDesigner Amityville NY
Graphisoft EcoDesigner is an integrated, easy-to-use energy evaluation tool for architects. EcoDesigner enables architects to control the energy consumption of their buildings, and sets new standards in sustainable design, making ArchiCAD the leading software solution for contemporary architectural demands.
- Hand Tools Amityville NY
- Festool C12 Cordless Drill Amityville NY
- Home Repair Tools Amityville NY
- Festool Joining System Amityville NY
- INNOVA® 3100 Tools Amityville NY
- Drywall Cutting and Multifunction Bench Amityville NY
- Hitachi KM 12VC Router Combination Kit Amityville NY
- Framing Square Amityville NY
- Hidden-Fastener Tool Amityville NY