Drainage System Testing Olean NY

Drainage pipes start from the first manhole or inspection chamber to the septic tank or sewer system in Olean. After laying the pipes, before use the drains should be tested. Each section in between the manholes should be tested.

Local Companies

Allegheny Store Fixtures, Inc.
(814) 362-6805
57 Holley Avenue
Bradford,, PA
Jim Wankel Home Improvements & More
(814) 966-3418
110 Sweitzer Drive
Duke Center, PA
Kightlinger Excavating, Inc.
(814) 368-5879
30 Main Street
Lewis Run, PA
Natures Design Landscaping
(814) 368-7527
9 South Gate Road
Bradford,, PA
Dallas-Morris Drilling, Inc.
(814) 362-6493
29 Morris Lane
Bradford,, PA
JST Construction
(716) 553-4028
2838 East Hill Rd.
Franklinville, NY
Clyne Builders
(814) 368-3644
233 South Avenue
Bradford,, PA
Kessel Construction, Inc.
(814) 362-4696
345 High Street
Bradford,, PA
E & M Engineers & Surveyors, PC
(814) 362-5546
24 Derrick Road
Bradford,, PA
Stewart Culligan Water Conditioning, Inc.
(814) 368-6123
P.O. Box 360
Bradford,, PA

Provided By:

Author: Andrew Karundu

Drainage pipes start from the first manhole or inspection chamber to the septic tank or sewer system. After laying the pipes, before use the drains should be tested. Each section in between the manholes should be tested. Its appropriate that this is done at least twelve hours after jointing the last pipe. There are various methods of checking the system. This ensures that the system is air tight to avoid foul smells and leakages along the lines.

The testing of drainage pipes after laying commences with the following method. First the lower end of the pipe and all junctions are securely stopped. The whole length is then filled with water. After filling with water, a stopper is inserted at the top leaving a pipe attached with drain plug. This pipe is bent at ninety degrees and terminated at an elevated tank. The vertical distance of elevation should be at least one meter. This will give gravity flow.

In testing the drainage pipes, water is poured into the header tank. This is kept full for atleast three hours. It allows absorption to take place. After this time, the tank is topped up and testing commences. After a period of thirty minutes have elapsed check the water level in the tank. The water level in the header tank should not have fallen. If has dropped by there millimeters then the test is satisfactory. Give one hour and check the levels.

After testing the drain pipes and they fail the test, check the point of leakage. Its important to note that tests are run on pipes laid in trenches but are not covered. The point of leakage is then noted and fixed. This is done using a strong concrete surround with fine aggregates. A minimum cover of one hundred and fifty millimeters is done. Tests are then done again and confirmed. After passing the test, back filling is then done for the trenches.

About the Author:

Andrew Karundu Is A Building Economist, Providing Home Based Solutions To Fixing, Repairing, Remodeling And Redesigning Homes. He Uses Simple Tried And Tested Methods To Improve Family Lifestyles.Visit His Site Here For Adequate Information On Most HOME IMPROVEMENT SOLUTIONS .

Article Source: http://www.articlesbase.com/remodeling-articles/how-to-test-drainage-pipes-after-laying-1069913.html

Related Articles
- Preventing Basement Floods Olean NY
If walking down to the basement leads you to a wading pool of water, you have a leak that needs fixing before more damage is done. Preventing these leaks is the best way to fight moisture in the basement. Some methods are as cheap as buying dirt and can keep you from constant cleanups or costly mold remediation.
- Growing Tomatoes Olean NY
- Gutters Olean NY
- Creating Herb Gardens Olean NY
- Fixtures and Products for the Bath Olean NY
- Central Heating System Olean NY
- How to Design and Install a Radiant Floor Heating System Olean NY
- Regular Roof Maintenance and Inspections Olean NY
- How to Diagnose and Clear Cloudy Swimming Pool Water Olean NY