Drainage System Testing Amsterdam NY

Drainage pipes start from the first manhole or inspection chamber to the septic tank or sewer system in Amsterdam. After laying the pipes, before use the drains should be tested. Each section in between the manholes should be tested.

Local Companies

Advanced Environmental Associates
(518)522-4406
2877 Rt.9
Malta, NY
Amity Pest Management
(315) 947-5960

Sterling, NY
Marchisio Andrew J
(518) 537-4030
99 Palatine Park Rd
Germantown, NY
General Home Inspectors Inc
(518) 383-4816
611 Riverview Rd
Rexford, NY
A A Quality Home Inspection Co
(315) 638-0865
7 Huckleberry Ln
Liverpool, NY
Residential One, LLC
518-383-3199
207 Riverview Road
Rexford, NY
Ethos Homes, LLC
518-275-5731
20 Jordan Ln
Glenville, NY
Independent Consolidated Inspection Services Inc
(315) 735-5233
1410 Albany St
Utica, NY
A-1 Home Inspections
(845) 889-8849

Staatsburg, NY
Scientific Control
(518) 743-0015
2303 Regency Park Apts N
Queensbury, NY

Provided By:

Author: Andrew Karundu

Drainage pipes start from the first manhole or inspection chamber to the septic tank or sewer system. After laying the pipes, before use the drains should be tested. Each section in between the manholes should be tested. Its appropriate that this is done at least twelve hours after jointing the last pipe. There are various methods of checking the system. This ensures that the system is air tight to avoid foul smells and leakages along the lines.

The testing of drainage pipes after laying commences with the following method. First the lower end of the pipe and all junctions are securely stopped. The whole length is then filled with water. After filling with water, a stopper is inserted at the top leaving a pipe attached with drain plug. This pipe is bent at ninety degrees and terminated at an elevated tank. The vertical distance of elevation should be at least one meter. This will give gravity flow.

In testing the drainage pipes, water is poured into the header tank. This is kept full for atleast three hours. It allows absorption to take place. After this time, the tank is topped up and testing commences. After a period of thirty minutes have elapsed check the water level in the tank. The water level in the header tank should not have fallen. If has dropped by there millimeters then the test is satisfactory. Give one hour and check the levels.

After testing the drain pipes and they fail the test, check the point of leakage. Its important to note that tests are run on pipes laid in trenches but are not covered. The point of leakage is then noted and fixed. This is done using a strong concrete surround with fine aggregates. A minimum cover of one hundred and fifty millimeters is done. Tests are then done again and confirmed. After passing the test, back filling is then done for the trenches.

About the Author:

Andrew Karundu Is A Building Economist, Providing Home Based Solutions To Fixing, Repairing, Remodeling And Redesigning Homes. He Uses Simple Tried And Tested Methods To Improve Family Lifestyles.Visit His Site Here For Adequate Information On Most HOME IMPROVEMENT SOLUTIONS .

Article Source: http://www.articlesbase.com/remodeling-articles/how-to-test-drainage-pipes-after-laying-1069913.html

Related Articles
- Central Heating System Amsterdam NY
Central heating is very different from local heating in the way heat is generated. In central heating, heat generation occurs in one place, such as a furnace room in a house or a mechanical room in a large building through the combustion of fossil fuel in a furnace or boiler.
- How to Diagnose and Clear Cloudy Swimming Pool Water Amsterdam NY
- How to Design and Install a Radiant Floor Heating System Amsterdam NY
- Growing Tomatoes Amsterdam NY
- Gutters Amsterdam NY
- Regular Roof Maintenance and Inspections Amsterdam NY
- Preventing Basement Floods Amsterdam NY
- Fixtures and Products for the Bath Amsterdam NY
- Creating Herb Gardens Amsterdam NY