Building Masonry Feature Walls Rome NY

Feature walls in Rome are made of materials like masonry, brickwork, resin coatings, timber, concrete and gypsum. This can be built up during construction of the house mostly concrete, timber, brickwork and masonry or cladded. For other types they are normally cladding's on finished walls. This are found in niches, above chimney breasts, lobby, lounge, bay window, dinning and family room walls.

Local Companies

Lowe's Home Improvement Warehouse of Rome
(315) 709-3000
1230 Erie Blvd W
Rome, NY
AAA Pic & Pay Lumber
(315) 337-1016
6895 Rome Oriskany Rd
Rome, NY
Vinyl Deck & Dock Distributors
(518) 377-0374
1563 State St
Schenectady, NY
Zamir Equities
(212) 269-7553
40 Broad St
New York, NY
Atlantic Coating Inc
(631) 259-2401
360 Magee St
Southampton, NY
Lou's Bargain Barn
(315) 336-0796
529 Erie Blvd W
Rome, NY
Bargain Depot
(315) 337-1016
6895 Rome Oriskany Rd
Rome, NY
General Lumber Hardware
(315) 336-2600
529 Erie Blvd W
Rome, NY
Lowes Home Improvement Warehouse of Ulster
(845) 382-6000
901 Frank Sottile Blvd
Kingston, NY
Smith's True Value Hardware Lumber and Gifts
(716) 934-4238
Routes 5 & 20
Irving, NY

Provided By:

How to make a masonry feature wall

Author: Andrew Karundu

Feature walls are made of materials like masonry, brickwork, resin coatings, timber, concrete and gypsum. This can be built up during construction of the house mostly concrete, timber, brickwork and masonry or cladded. For other types they are normally claddings on finished walls. This are found in niches, above chimney breasts, lobby, lounge, bay window, dinning and family room walls. The level of works determines the type of finish to be used.

When making feature walls, the location is very important. For niches coats have good aesthetic as they are rich in color. When working in the rooms check the corresponding finish to give a contrast to the wall. Commence the work by hacking off the surfaces for finished walls to receive the finish. Use chisel dressed fair face stones with a thickness of one inch. Cut the stones into slates of atleast one foot in length and various widths.

In masonry feature wall construction, stone slates are patterned as desired. Use a straight edge at the bottom to level the works. Spread cement grouting to the pieces and commence working from the bottom upwards. Lay the pieces block wise to the end of hacked area. Remember to pound them to spread the cement behind to avoid hollow spaces. Use joint less bonding. Keep joints alternate on each row to the top and complete marked area. Brush off cement.

After the feature masonry wall is complete, rake out the bonding horizontal joints. Use a rounded bar of a quarter inch for horizontal key pointing. Remove arising debris and make good floor joint if the wall had commenced from the floor. When this is done give a week and to allow curing. Paint clear vanish in Matt or gloss as desired. For a rustic finish don't varnish. The method can be repeated for brickwork, rustic tiles, rubble and grano materials.

About the Author:

Andrew Karundu Is A Building Economist, Providing Home Based Solutions To Fixing, Repairing, Remodeling And Redesigning Homes. He Uses Simple Tried And Tested Methods To Improve Family Lifestyles.Visit His Site Here For Adequate Information On Most HOME IMPROVEMENT SOLUTIONS .

Article Source: http://www.articlesbase.com/remodeling-articles/how-to-make-a-masonry-feature-wall-991942.html

Related Articles
- Integrating Parapet and Roofing Flashing Rome NY
On the inside face of a parapet or wherever a masonry wall intersects a lower roof, I have seen cases where the masonry flashing exits the wall one or more courses above the top of the retaining bar for the roof base flashing.
- Saving Water and Money Rome NY
- Using Wrought Iron Wall Decor to Accent White Walls Rome NY
- Getting Your Home in Shape for Summer Rome NY
- How to Clean a Fireplace Rome NY
- Interior Stucco Walls Rome NY
- Powered Hand Tools Rome NY
- How to Clean a Shower/Tub the Easy Way Rome NY
- Brick Work Rome NY
- How to Clean Any Room Rome NY