Building Masonry Feature Walls Beacon NY

Feature walls in Beacon are made of materials like masonry, brickwork, resin coatings, timber, concrete and gypsum. This can be built up during construction of the house mostly concrete, timber, brickwork and masonry or cladded. For other types they are normally cladding's on finished walls. This are found in niches, above chimney breasts, lobby, lounge, bay window, dinning and family room walls.

Local Companies

Arcade Lumber
(585) 492-2700
430 Main St
Arcade, NY
Rowley Building Products
(845) 343-7742
15 Golf Links Rd
Middletown, NY
Jerusalem Stone Dept
(718) 783-2527
1072 Atlantic Ave
Brooklyn, NY
Florence Building Materials
(631) 653-6600
RR 104
East Quogue, NY
Quality Fencing Inc
(516) 437-1647
116 S 2nd St
New Hyde Park, NY
Goodwin Assocs
(585) 248-3320
PO Box 18605
Rochester, NY
Sam's Lumber Co
(716) 549-1212
8578 Erie Rd
Angola, NY
Long Island Paneling Ceilings & Floors
(631) 563-6114
4769 Sunrise Hwy
Bohemia, NY
Corcon Inc
(718) 684-1852
4260 Throggs Neck Exprwy
Bronx, NY
A H Harris and Sons
(716) 667-3355
3605 California Rd
Orchard Park, NY

Provided By:

How to make a masonry feature wall

Author: Andrew Karundu

Feature walls are made of materials like masonry, brickwork, resin coatings, timber, concrete and gypsum. This can be built up during construction of the house mostly concrete, timber, brickwork and masonry or cladded. For other types they are normally claddings on finished walls. This are found in niches, above chimney breasts, lobby, lounge, bay window, dinning and family room walls. The level of works determines the type of finish to be used.

When making feature walls, the location is very important. For niches coats have good aesthetic as they are rich in color. When working in the rooms check the corresponding finish to give a contrast to the wall. Commence the work by hacking off the surfaces for finished walls to receive the finish. Use chisel dressed fair face stones with a thickness of one inch. Cut the stones into slates of atleast one foot in length and various widths.

In masonry feature wall construction, stone slates are patterned as desired. Use a straight edge at the bottom to level the works. Spread cement grouting to the pieces and commence working from the bottom upwards. Lay the pieces block wise to the end of hacked area. Remember to pound them to spread the cement behind to avoid hollow spaces. Use joint less bonding. Keep joints alternate on each row to the top and complete marked area. Brush off cement.

After the feature masonry wall is complete, rake out the bonding horizontal joints. Use a rounded bar of a quarter inch for horizontal key pointing. Remove arising debris and make good floor joint if the wall had commenced from the floor. When this is done give a week and to allow curing. Paint clear vanish in Matt or gloss as desired. For a rustic finish don't varnish. The method can be repeated for brickwork, rustic tiles, rubble and grano materials.

About the Author:

Andrew Karundu Is A Building Economist, Providing Home Based Solutions To Fixing, Repairing, Remodeling And Redesigning Homes. He Uses Simple Tried And Tested Methods To Improve Family Lifestyles.Visit His Site Here For Adequate Information On Most HOME IMPROVEMENT SOLUTIONS .

Article Source: http://www.articlesbase.com/remodeling-articles/how-to-make-a-masonry-feature-wall-991942.html

Related Articles
- Integrating Parapet and Roofing Flashing Beacon NY
On the inside face of a parapet or wherever a masonry wall intersects a lower roof, I have seen cases where the masonry flashing exits the wall one or more courses above the top of the retaining bar for the roof base flashing.
- Getting Your Home in Shape for Summer Beacon NY
- Saving Water and Money Beacon NY
- How to Clean Any Room Beacon NY
- How to Clean a Fireplace Beacon NY
- Brick Work Beacon NY
- Interior Stucco Walls Beacon NY
- Using Wrought Iron Wall Decor to Accent White Walls Beacon NY
- How to Clean a Shower/Tub the Easy Way Beacon NY
- Powered Hand Tools Beacon NY