Building Masonry Feature Walls Auburn NY

Feature walls in Auburn are made of materials like masonry, brickwork, resin coatings, timber, concrete and gypsum. This can be built up during construction of the house mostly concrete, timber, brickwork and masonry or cladded. For other types they are normally cladding's on finished walls. This are found in niches, above chimney breasts, lobby, lounge, bay window, dinning and family room walls.

Local Companies

Schneid Construction
(315) 479-9004
210 6th St
Syracuse, NY
North Main Lumber
(315) 252-8392
341 Grant Avenue Rd
Auburn, NY
Casters Sawmill Inc
(315) 387-5104
6323 US Route 11
Sandy Creek, NY
Curtis Lumber Co Inc
(518) 885-5311
885 State Route 67
Ballston Spa, NY
Nunda Lumber & Hardware Inc
(585) 468-2521
11 N State St
Nunda, NY
Expert Chimney
(315) 469-5004
4800 Mcdonald Rd Ste 1
Syracuse, NY
Callahan Masonry Supply
(315) 252-7596
117 York St
Auburn, NY
T & K Hardware & Home Center
(315) 258-9481
76 State St
Auburn, NY
Burke Home Center
(315) 343-6147
38 E 2nd St
Oswego, NY
Scara-Mix Inc
(718) 442-7357
2537 Richmond Ter
Staten Island, NY

Provided By:

How to make a masonry feature wall

Author: Andrew Karundu

Feature walls are made of materials like masonry, brickwork, resin coatings, timber, concrete and gypsum. This can be built up during construction of the house mostly concrete, timber, brickwork and masonry or cladded. For other types they are normally claddings on finished walls. This are found in niches, above chimney breasts, lobby, lounge, bay window, dinning and family room walls. The level of works determines the type of finish to be used.

When making feature walls, the location is very important. For niches coats have good aesthetic as they are rich in color. When working in the rooms check the corresponding finish to give a contrast to the wall. Commence the work by hacking off the surfaces for finished walls to receive the finish. Use chisel dressed fair face stones with a thickness of one inch. Cut the stones into slates of atleast one foot in length and various widths.

In masonry feature wall construction, stone slates are patterned as desired. Use a straight edge at the bottom to level the works. Spread cement grouting to the pieces and commence working from the bottom upwards. Lay the pieces block wise to the end of hacked area. Remember to pound them to spread the cement behind to avoid hollow spaces. Use joint less bonding. Keep joints alternate on each row to the top and complete marked area. Brush off cement.

After the feature masonry wall is complete, rake out the bonding horizontal joints. Use a rounded bar of a quarter inch for horizontal key pointing. Remove arising debris and make good floor joint if the wall had commenced from the floor. When this is done give a week and to allow curing. Paint clear vanish in Matt or gloss as desired. For a rustic finish don't varnish. The method can be repeated for brickwork, rustic tiles, rubble and grano materials.

About the Author:

Andrew Karundu Is A Building Economist, Providing Home Based Solutions To Fixing, Repairing, Remodeling And Redesigning Homes. He Uses Simple Tried And Tested Methods To Improve Family Lifestyles.Visit His Site Here For Adequate Information On Most HOME IMPROVEMENT SOLUTIONS .

Article Source: http://www.articlesbase.com/remodeling-articles/how-to-make-a-masonry-feature-wall-991942.html

Related Articles
- How to Clean a Shower/Tub the Easy Way Auburn NY
Do you LOVE a sparkling clean shower stall but HATE cleaning one? Me too! I started using this method about 20 years ago out of necessity because I had to clean 6-8 bathrooms a day thoroughly and QUICKLY while working for a residential cleaning service.
- Integrating Parapet and Roofing Flashing Auburn NY
- Getting Your Home in Shape for Summer Auburn NY
- How to Clean a Fireplace Auburn NY
- Powered Hand Tools Auburn NY
- How to Clean Any Room Auburn NY
- Interior Stucco Walls Auburn NY
- Saving Water and Money Auburn NY
- Brick Work Auburn NY
- Using Wrought Iron Wall Decor to Accent White Walls Auburn NY